Rainbow-electronics MAX1885 Manual do Utilizador Página 31

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 38
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 30
MAX1778/MAX1880–MAX1885
Quad-Output TFT LCD DC-DC
Converters with Buffer
______________________________________________________________________________________ 31
Input-Output (Dropout) Voltage and Startup
A linear regulators minimum input-to-output voltage dif-
ferential (dropout voltage) determines the lowest use-
able supply voltage. Because the MAX1778/
MAX1881/MAX1883/MAX1884 use an internal PNP
transistor (or external NPN transistor), their dropout
voltage is a function of the transistors collector-to-emit-
ter saturation voltage (see Typical Operating
Characteristics). The linear regulators quiescent cur-
rent increases when in dropout.
The internal linear regulator will try to start up once its
supply voltage (V
SUPL
) exceeds 4V. When the linear
regulator powers up, the linear regulator may be in
dropout if the linear regulators output set voltage is
higher than its input supply voltage. Therefore, during
this brief period, the linear regulator draws additional
supply current until the input supply voltage exceeds
the output set voltage plus the pass transistors satura-
tion voltage (V
LDO(SET
) + V
CE(SAT)
).
VCOM Buffer (Operational
Transconductance Amplifier)
Buffer Output Voltage and Capacitor Selection
The positive input (BUF+) features dual mode opera-
tion. Connect BUF+ to GND for the preset VSUPB/2
output voltage, set by an internal 50% resistive-divider.
Adjust the amplifiers output voltage by connecting a
voltage-divider from SUPB to BUF+ to GND (Figure 6).
Select R12 in the 10k to 100k range. Calculate R11
with the following equation:
where V
SUPB
may range from 4.5V to 13V, and V
BUF+
may range from 1.2V to (V
SUPB
- 1.2V). Connect a mini-
mum 1µF ceramic capacitor from BUFOUT to ground.
PC Board Layout and Grounding
Careful PC board layout is extremely important for
proper operation. Follow the following guidelines for
good PC board layout:
1) Place the main step-up converter output diode and
output capacitor less than 0.2in (5mm) from the LX
and PGND pins with wide traces and no vias.
2) Separate analog ground and power ground. The
ground connections for the step-up converters and
charge pumps input and output capacitors should
be connected to the power ground plane. The lin-
ear regulators and VCOM buffers input and output
capacitors should be connected to a separate
power-ground path, star-connected to the PGND
pin to minimize voltage drops. When using multi-
layer boards, the top layer should contain the boost
RR
V
V
SUPB
BUF
11 12 1 =
+
-
IN
SHDN
LDOOUT
LX
L1
6.8µH
INPUT
V
IN
= 3.3V
C1
0.22µF
C
OUT
(2) 4.7µF
C
IN
4.7µF
R1
274k
R2
49.9k
FB
GND
FBL
REF
Q1
INTG
PGND
C
REF
0.22µF
MAX1778
MAX1883
(MAX1881)*
(MAX1884)*
R3
49.9k
R4
49.9k
C
LDO
1µF
C3
0.01µF
C2
0.01µF
C
LDOOUT
4.7µF
C
LDOIN
1µF
R5
1.5k
MAIN
V
MAIN
= 8V
LDO
V
LDO
= 2.5V
SUPL
Figure 7. External Linear Regulator
Vista de página 30
1 2 ... 26 27 28 29 30 31 32 33 34 35 36 37 38

Comentários a estes Manuais

Sem comentários