Rainbow-electronics MAX1800 Manual do Utilizador Página 4

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 24
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 3
MAX1800
Digital Camera Step-Up
Power Supply
4 _______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS (continued)
(Circuit of Figure 1, V
OUT
= V
POUT
= 3.3V, PGND = GND, V
ONM
= 3.3V, V
ON1
= V
ON2
= V
ON3
= V
ONA
= 0, T
A
= -40°C to +85°C,
unless otherwise noted. Typical values are at T
A
= +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
ANALOG GAIN BLOCK
AI Feedback Regulation Voltage V
AO
= V
OUT
- 1.25V 1.23 1.25 1.27 V
AI Input Common-Mode Range -0.1 1.3 V
AI Input Current V
AI
= 1.35V 100 nA
AI to AO Voltage Gain 70 100 140 V/V
AO Output Sink Current V
AI
= 1V, V
AO
= 2V 0.5 2.5 mA
AO Output Source Current V
AI
= 1.5V, V
AO
= 2V 0.5 2.5 mA
AO Output Low Voltage V
AI
= 1V, I
SINK
= 25µA 0.5 V
AO Output High Voltage V
AI
= 1.5V or V
ONA
= 0, I
SOURCE
= 25µA
V
POUT
- 0.5
V
AI to AO -3dB Bandwidth 5 MHz
AUXILIARY DC/DC CONTROLLERS 1, 2, 3
INTERNAL CLOCK
OSC Clock Low Trip Level Falling edge 0.2 0.25 0.3 V
V
DCON
= 0.625V 0.575 0.625 0.675
OSC Clock High Trip Level
V
DCON
= V
OUT
1.00 1.05 1.10
V
Maximum Duty-Cycle
Adjustment Range
40 90
%
Maximum Duty Cycle V
DCON
_ = 0.625V 50 %
Default Maximum Duty Cycle V
DCON
_ = 1.25V 84 %
ERROR AMPLIFIER
FB_ Regulation Voltage FB_ = COMP_ 1.23 1.25 1.27 V
FB_ to COMP_
Transconductance
FB_ = COMP_, -5µA < I
LOAD
< +5µA 60 100 140 µS
FB_ to COMP_ Maximum
Voltage Gain
2000 V/V
FB_ Input Leakage Current V
FB
_ = 1.35V 100 nA
DRIVERS (DL1, DL2, DL3)
DL_ Driver Resistance R
ON
Output high or low 2 6
DL_ Drive Current Sourcing or sinking, V
DL
_ = V
OUT
/2 0.5 A
SOFT-START
Soft-Start Interval 1024
OSC
cycles
SHORT-CIRCUIT PROTECTION
Fault Interval 1024
OSC
cycles
Note 1: Specifications to -40°C are guaranteed by design and not production tested.
Note 2: Operating voltage. Since the regulator is bootstrapped to the output, once started it will operate down to +0.7V input.
Note 3: The regulator is in startup mode until the voltage is reached.
Vista de página 3
1 2 3 4 5 6 7 8 9 ... 23 24

Comentários a estes Manuais

Sem comentários