
MAX1765
800mA, Low-Noise, Step-Up DC-DC Converter
with 500mA Linear Regulator
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V
OUT
= V
POUT
= V
INL
= V
ONA
= V
ONL
= 3.6V, CLK/SEL = FBL = ONB = TRACK = PGND = GND, ISET = REF (bypassed with
0.22µF), LX = open, OUTL = open (bypassed with 4.7µF), T
A
= 0°C to +85°C, unless otherwise noted. Typical values are at
T
A
= +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ONA, ONB, ONL, TRACK, OUT, INL to GND..............-0.3V, +6V
PGND to GND.....................................................................±0.3V
LX to GND ...............................................-0.3V to (POUT + 0.3V)
OUTL to GND ..............................................-0.3V to (INL + 0.3V)
CLK/SEL, REF, FB, FBL, ISET, POUT
to GND...................................................-0.3V to (OUT + 0.3V)
OUTL Short Circuit .....................................................Continuous
Continuous Power Dissipation (T
A
= +70°C)
16-Pin QSOP (derate 8.3mW/°C above +70°C)...........667mW
16-Pin TSSOP-EP (derate 19mW/°C above +70°C) ....1500mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
DC-DC CONVERTER
Input Voltage Range (Note 1) 0.7 5.5 V
INL Voltage Range (Note 1) 2.3 5.5 V
Minimum Startup Voltage I
LOAD
< 1mA, T
A
= +25°C, Figure 2 0.9 1.1 V
Temperature Coefficient of
Startup Voltage
I
LOAD
< 1mA -2 m V /°C
FB Regulation Voltage V
FB
CLK/SEL = OUT, 0 < I
LX
< 0.55A 1.215 1.250 1.275 V
FB Input Leakage Current V
FB
= 1.35V 0.01 100 nA
Output Voltage Adjust Range 2.5 5.5 V
Load Regulation CLK/SEL = OUT, 0 < I
LOAD
< 800mA -1 %
OUT Voltage in Track Mode V
OUTL
> 2.0V, INL = POUT
V
OUTL
+ 0.4
V
OUTL
+ 0.5
V
OUTL
+ 0.6
V
Frequency in Startup Mode f
LX
V
OUT
= 1.5V 125 1000 kHz
Startup to Normal Mode
Transition Voltage
Rising edge only (Note 2) 2.00 2.15 2.30 V
ISET Input Leakage Current V
ISET
= 1.25V 0.01 50 nA
Supply Current in Normal Mode
(Note 3)
CLK/SEL = ONL = GND, no load 100 200 µA
V
FB
= 1.5V 130 200 µA
Supply Current in Low-Noise
PWM Mode (Note 3)
C LK/S E L = OU T,
no l oad
FB = GN D ( LX sw i tchi ng ) 2.5 mA
Supply Current in Shutdown ONA = ONL = GND, ONB = OUT 1 10 µA
Comentários a estes Manuais